$76.99 – $216.99
– Our Superclear Liquid Glass Deep Pour Epoxy can be poured anywhere between 2-4” with ease!
– SuperClear 2.0 cures rock-hard, giving you unparalleled structural integrity, and is able to withstand years of wear & tear without a problem!
– Liquid Glass Epoxy is a low viscosity formulation that effortlessly allows for bubbles to rise to the surface as it cures. Giving you a crystal clear finish every time!
– Fiberglass Coatings, Inc. is based out of Saint Petersburg, FL and has been in business for over 60 years! We are proud to say we are made 100% in the USA!
-
Our Liquid Glass Deep Pour Epoxy is absolutely unparalleled with a deep pour capability of 2-4 inches and gives you unmatched industry performance, convenience by eliminating 75% of your work, and the clearest finish you can get on the market today!
Using the Coverage Chart, determine the amount of epoxy you will need for your project. Be sure to order SuperClear Table Top Epoxy for a seal coat to ensure best results!
Ensure your working environment is clean, dry and at least 70 degrees for best results. Lay down a plastic sheeting below your project for a safe, easy cleanup. Make sure your surface is completely level, as the epoxy will self-level.
Seal Coat – Be sure to clean the surface with Isopropyl Alcohol 90% + and apply your sealcoat with a brush, following all mixing directions for that product. Let it get tacky before pouring your deep pour. If the seal layer is fully cured, for best results, lightly sand the surface with 320 grit sandpaper and clean with Isopropyl Alcohol 90% +, and then pour the deep pour.
Mixing Deep Pour – Measure 2 parts Resin to 1 part Activator and pour into a clean, dry bucket or cup. Stir the mixture for at least 5 minutes with either a stir stick (if mixing with a stir stick, do not mix more than 1 quart) or a drill mixer set to low. Ensure you are not whipping air into your epoxy. Be sure to scrape the sides and bottom to ensure all of your epoxy is properly mixed.
Transfer contents to a new, clean, dry bucket or cup and continue mixing for 3 more minutes to ensure proper mixing, again scraping sides and bottom.
Pour mixture directly into your mold at your desired depth. Do not scrape the bucket at this time. If you do, you risk scraping in unmixed material that has clung to the sides or bottom. This would result in soft spots and/or hotspots.
Use a heat source, like a heat gun to remove any air bubbles. Start at 6” minimum above the surface and sweep back and forth until no bubbles remain. Do not leave the heat gun over the surface too long, if you do, it may result in surface distortions.
Allow the surface to cure, up to 72 hours in a dust-free environment. The epoxy will start to get tacky after 24 hours but do not disturb for 72 hours to ensure a proper cure.
– You need to stir it by hand for a minimum of 5 minutes, scraping the sides and bottom thoroughly throughout while mixing. When pouring, we do not recommend scraping the sides. Doing so can risk mixing in unmixed, unincorporated epoxy into your pour, thus creating curing issues.
– You can pour up to 4” thick per pour, depending on ambient temperature and total mass. Much thicker than most competitors! The mass for a 4” pour varies depending on temperatures and conditions. If you have never poured a deep pour at 4”, we suggest you try it on a smaller scale to understand how it will cure in your particular environment.
– The product will begin to harden within the first 12-24 hours in ideal conditions, but takes 48-72 hours to completely cure, depending upon conditions like constant temperature, humidity, mass and airflow.
– Yes! Simply wait until the pour is tacky and nearly hard and pour your next layer. If the product is already hard, lightly sand with 220-320 grit sandpaper and wipe it down with Isopropyl Alcohol 90% or higher before adding additional layers, which helps with the adhesion between the two layers.
| Weight | N/A |
|---|---|
| Dimensions | N/A |
| Shelf Life | Unopened: 6 – 12 months* *depending upon how the product is stored. |
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet.