FREE SHIPPING ON ALL ORDERS OVER $150!
$112.49
– Superclear® WB Primer & Sealer creates a premium grade primed and sealed surface to prepare for an epoxy resin pour! Works in conjunction with our Superclear® Countertop Epoxy!
– Compatible with a variety of substrates, Superclear® WB Primer & Sealer has strong adhesion to create a lasting bond between surfaces and epoxy!
– With three striking color options, Superclear® WB Primer & Sealer provides epoxy with strong backing to make colors pop!
– Fiberglass Coatings, Inc. is based out of Saint Petersburg, FL and has been in business for over 60 years! We are proud to say we are made 100% in the USA!
-
Our Superclear® WB Primer & Sealer is the ideal system to prime and seal surfaces before applying epoxy resin. Compatible with most substrates, this water activated priming and sealing product offers the strongest bond, seal, and color backing for epoxy.
Use in conjunction with our Superclear® Countertop Epoxy!
Using the Coverage Chart, determine the amount of epoxy you will need for your project. Lightly sand the surface of your substrate to assist in primer bonding and clean with Superclean or Isopropyl Alcohol (90% or higher). Apply tape to any areas that will not require priming and sealing.
Ensure your working environment is clean, dry and at least 70 to 84 degrees for best results. Lay down a plastic sheeting below your project for a safe, easy cleanup. Make sure your surface is completely level, as the epoxy will self-level.
Shake the A and B side jugs vigorously to agitate the product. If the material is not properly agitated, it may not cure properly.
Measure 2 parts Resin to 1 part Activator and pour into a clean, dry bucket or cup. Add 20-30% distilled water to the mixture. Stir the mixture for at least 5 minutes with a drill mixer set to low. Ensure you are not whipping air into your epoxy. Be sure to scrape the sides and bottom to ensure all of your epoxy is properly mixed.
Transfer contents to a new, clean, dry bucket or cup and continue mixing for 5 more minutes to ensure proper mixing, again scraping sides and bottom.
Apply a thin, even coating to the surface with a foam roller or paintbrush. Be careful not to apply too thick, or water blisters will form.
Allow the material to become hard and tacky to the touch before applying Superclear® Countertop Epoxy Resin.
– You need to stir it by hand for a minimum of 10 minutes, scraping the sides and bottom thoroughly throughout while mixing.
– WB Primer & Sealer is similar to paint in terms of application, so it should be applied in a thin, even coating. The thickness of your prime and seal coat will depend on a variety of factors, including the amount of water added, surface preparation, surface porosity, temperature, humidity, mass, and airflow. If you have never poured a thick, we suggest you try it on a smaller scale to understand how it will cure in your particular environment.
– The product will feel cured in 1 to 8 hours, depending upon conditions like the amount of water added, constant temperature, humidity, mass and airflow.
– Yes! Simply wait until the pour is at least tacky and nearly hard and pour your next layer. If the product is already hard, clean the surface with Superclearn or Isopropyl Alcohol (90% or higher) before adding another layer.
While our product can be used in a variety of applications, not all users or environments are the same. As such, specific directions for all individual users might not be addressed in the directions. If there are any questions that our directions do not answer, pertaining to the individual customer’s application, it is the customer’s sole responsibility to contact us directly with any technical questions and procedures prior to the application of the product. See below for various means to obtain further information and or contact us directly; we offer FAQs on our website and technical service via Email or phone Monday through Friday, 9am-4pm EST.
For more product information, please visit:
www.SuperEpoxySystems.com
(888) 849-0588
superclear@fgci.com
Temperature : Volume & Depth Info
Always pour in a temperature controlled environment. Ideal working temperatures are 70°F to 84°F, but this is dependent on the total volume and depth of the project. The greater the volume or thickness of the pour, the lower your temperatures should be.
| Weight | N/A |
|---|---|
| Shelf Life | Unopened: 6 – 12 months* *depending upon how the product is stored. |
Reviews
There are no reviews yet.